Systematic analysis and multi-objective optimization of an integrated power and freshwater production cycle

This study represents the results of the analysis and optimization of an integrated system for cogenerating electricity and freshwater. This setup consists of a Solid Oxide Fuel cell (SOFC) for producing electricity. Unburned fuel of the SOFC is burned in the afterburner to increase the temperature of the SOFC's outlet gasses and operate a Gas turbine (GT) to produce additional power and operate the air compressor. At the bottom of this cycle, a combined setup of a Multi-Effect Desalination (MED) and Reverse Osmosis (RO) is considered to produce freshwater from the unused heat capacity of the GT's exhaust gasses. Also, a Stirling engine is used in the fuel supply line to increase the fuel's temperature. Using LNG and the Stirling engine will replace the fuel compressor with a pump which increases the system performance and eliminates the need for the expansion valve. To study the system performance a mathematical model is developed in Engineering Equation Solver (EES) program. Then, the system's simulated data from the EES has been sent to MATLAB to promote the best operating condition based on the optimization criteria. An energetic, exergetic, economic, and environmental analysis has been performed and a Non-dominated Sorting Genetic Algorithm (NSGA-II) is used to achieve the goal. The two-objective optimization is performed to maximize the exergetic efficiency of the proposed system while minimizing the system's total cost of production. This cost is a weighted distribution of the Levelized Cost of Electricity (LCOE) and Levelized Cost of freshwater (LCOW). The results showed that the exergetic and energetic efficiencies of the system can reach 73.5% and 69.06% at the optimum point. The total electricity production of the system is 99 MW. The production cost is 11.71 Cents/kWh, of which 1.04 Cents/kWh is emission-related and environmental taxes. The freshwater production rate is 42.44 kg/s which costs 4.38 USD/m³.     

Novel proton-conducting layered perovskite based on BaLaInO4 with two different cations in B-sublattice: Synthesis,hydration, ionic (O2−, H+) conductivity

The present study focused on the novel material with significantly improved properties for the application in the area of clean energy. The new complex oxide BaLaIn_0·5Y_0·5O₄ with layered perovskite structure was obtained for the first time. It was proved that the introduction of Y³⁺ ions in the perovskite layer of BaLaInO₄ leads i) to the rise of the oxygen-ionic conductivity due to the increase in mobility of oxygen ions as a result of the expand of the cell volume and ii) to the enhancement of protonic conductivity due to the increase in the proton concentration and mobility. The sample BaLaIn_0·5Y_0·5O₄ is nearly pure proton conductor below 400 °C and has the protonic conductivity value 1.6?10^?5 S/cm at this temperature.     

High voltage and self-healing zwitterionic double-network hydrogels as electrolyte for zinc-ion hybrid supercapacitor/battery

The hydrogel electrolyte is an important part of safety and development potential in zinc-based energy storage equipment due to its inherent low mechanical strength and voltage decomposition. However, hydrogel electrolytes possess a reduced working life for zinc dendrites growth and a narrow voltage window. In this study, a hydrogel electrolyte prepares by the zwitterionic monomer [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl) (MS) and sodium alginate (SA) alleviate these problems. The zwitterionic double-network hydrogel has good mechanical strength, inhibits the growth of zinc dendrites, enhances practicability, greatly increases the voltage window (0–2.4 V), and has self-healing properties to its rich functional groups. The assembled zinc-ion hybrid supercapacitors (ZHSs) have a high-power density of 172.33 W kg^?1 and an energy density of 88.56 Wh·kg^?1 at 0.5 A g^?1. The assembled zinc-ion battery also has good electrochemical performance. Flexible ZHSs and batteries provide power to the timer stably under different bending angles. The zwitterionic double-network hydrogel can be applied to both zinc-based supercapacitors and batteries.     

Adjusting electronic structure coupling of Fe–Ni2P (NiFeP-MOF) multilevel structure for ultra-activity and durable catalytic water oxidation

Efficient electrocatalyst for alkaline oxygen evolution reaction is the critical core to the wide application of metal-air energy storage and water electrolysis hydrogen energy. Therefore, appropriate design of highly active and stable non-noble metal oxygen evolution electrocatalyst with good electronic structure and multilevel structure is both a goal and a challenge. Here, we report a Fe–Ni₂P electrocatalyst (NiFeP-MOF) with multilevel structure, which was obtained by anion exchange on the basis of Fe–Ni(OH)₂ (NiFe-MOF) grown on nickel foam in situ by solvothermal method. As expected, Fe substitution regulates the Ni oxidation state in the NiFeP-MOF and realizes electronic structure coupling, showing a highly active and stable oxygen evolution reaction (OER) in alkaline electrolyte solution. Specifically, the NiFeP-MOF demonstrates an ultralow overpotentials (232 mV, 10 mA cm^?2; 267 mV 100 mA cm^?2), respectively, an extremely small Tafel slope (34 mV dec^?1). Separately, the electrocatalyst shows an excellent cycle stability at 10 mA cm^?2 for 12 h (43,200 s). More importantly, this work come up with an available policy for the preparation of excellent alkaline hydrolysis electrolysis catalysts and air cathodes with excellent performance.     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Cloning,sequencing and structural analysis of membrane-bound polyphenol oxidase from Granny Smith apples (Malus × domestica Borkh)

The gene sequence coding for the membrane-bound polyphenol oxidase (mPPO) with a length of 1761 bp was cloned by PCR method and shown to contain one highly conserved sequence encoding a di-copper-binding region. The predicted three-dimensional structure of mPPO indicated that the active site was located near two copper ions and composed of a typical bundle of four α-helices. Each of the two catalytic copper ions was coordinated with three histidine residues in the hydrophobic pocket, yielding His 180, His 201, His 210, His 332, His 336 and His 366. Docking studies showed that 4-methylcatechol and chlorogenic acid have different binding models due to different ligand sizes and binding sites in the active centre, and it was found that the smaller compound exhibited a higher affinity for mPPO. Molecular dynamic simulation results indicated that Phe 353 is important in controlling enzymatic activity through influencing substrate coordination in the active site.     

Observation of table-like magnetocaloric effect and large refrigerant capacity in Nd6Fe13Pd1–xCux compounds

The table-like magnetocaloric effect is significant for the magnetic refrigeration applications above 20 K based on the Ericsson cycle. Herein, we prepared a series of Nd₆Fe₁₃Pd_1–xCu_x (x = 0.05, 0.1, 0.15) compounds by the arc-melting method. These compounds show the single crystalline phase in the tetragonal Nd₆Fe₁₃Si-type structure with the space group I4/mcm. A magnetic phase transition from ferromagnetism to antiferromagnetism and a metamagnetic transition from the antiferromagnetic state to the ferromagnetic state are observed in each of the compounds. The compounds exhibit table-like magnetocaloric effects with large refrigerant capacities. A constant ΔS_M in a temperature span of 40 K in the Nd₆Fe₁₃Pd_0.85Cu_0.15 compound are observed. For a field change of 0–5 T, the peak values of –ΔS_M for the Nd₆Fe₁₃Pd_0.95Cu_0.05, Nd₆Fe₁₃Pd_0.90Cu_0.10, and Nd₆Fe₁₃Pd_0.85Cu_0.15 compounds are estimated to be 4.8, 4.6 and 4.4 J/(kg·K) with corresponding refrigerant capacity values of 323, 331 and 316 J/kg, respectively. The obtained table-like magnetocaloric effects with large refrigerant capacities as well as fairly small thermal and magnetic hysteresis deem these series of compounds good candidates for single-phase magnetic refrigeration based on the Ericsson cycle.     

基于BIM超高层密集布筋区埋入式型钢混凝土柱脚施工技术

以漳州市某超高层项目为例,针对超高层密集布筋区埋入式型钢柱脚与钢筋的深化设计、地脚螺栓的定位预埋、型钢柱脚支撑体系设计、节点钢筋穿插连接施工、埋入式型钢柱脚安装等方面,提出切实可行的施工方法,解决了埋入式型钢混凝土柱脚的地脚螺栓精准预埋、与底板密集钢筋穿插连接施工、悬空支撑稳定等一系列施工技术难题,既满足了设计方案的要求,又可为类似工程提供借鉴。     

“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

Electrochemical performance of in situ LiFePO4 modified by N-doped graphene for Li-ion batteries

LiFePO₄ modified by N-doped graphene (NG) with a three-dimensional conductive network structure was synthesized via a one-step in situ hydrothermal method. The effects of N amount of NG on the phase structure, morphology, and electrochemical properties of LiFePO₄ are investigated in this study. X-ray diffraction (XRD) results show that doping suitable N amounts in NG do not alter the crystal structure of LiFePO_4, and scanning electron microscopy (SEM) images show that NG can slightly reduce the particle size of LiFePO₄. The high-resolution transmission electron microscopy (HRTEM) results show that the LiFePO₄ particles are well covered and connected by NG. The electrochemical performance confirms that LiFePO₄ modified by 20% N-doped graphene (named LFP/NG-4) displays a perfect specific capacity of 166.6 mAh·g^?1 at a rate of 0.2C and can reach 125 mAh·g^?1 at a rate of 5 C. Electrochemical impedance spectroscopy (EIS) results illustrate that the charge transfer resistance value of the LFP/NG-4 composite is only 58.6 Ω, which is very low compared with LiFePO₄. Cyclic voltammetry (CV) tests indicate that the addition of 20% N-doped graphene can effectively reduce electrode polarization and improve reversibility. The LFP/NG-4 composite with a three-dimensional conductive network structure can be regarded as a promising cathode material for Li-ion batteries.